FreeIPA and NFSv4

From Linux NFS

(Difference between revisions)
Jump to: navigation, search
(→Mount the filesystem)
(Replaced content with "This has been moved to NFS and FreeIPA.")
 
(47 intermediate revisions not shown)
Line 1: Line 1:
-
This document describes using NFSv4 with [http://freeipa.org/page/Main_Page FreeIPA].
+
This has been moved to [[NFS and FreeIPA]].
-
 
+
-
Historically, configuring a secure NFSv4 export (or even a client) has been challenging, especially when it requires setting up of a [http://en.wikipedia.org/wiki/Kerberos_(protocol) Kerberos] realm.
+
-
FreeIPA provides a packaged service of [http://en.wikipedia.org/wiki/Kerberos_(protocol) Kerberos 5], [http://en.wikipedia.org/wiki/LDAP LDAP] and helper software (ntp, httpd for admin interface, etc) with both a cli and web-based admin interface.
+
-
 
+
-
= Notes =
+
-
 
+
-
*These instructions are for [http://www.fedora.org/ Fedora 15].  Other distros will require similar setup - the key differences will be:
+
-
**a package installation tool other than yum
+
-
**a different config file layout
+
-
 
+
-
*This example uses a private network (192.168.56.0/24) with a fake DNS realm (example.fake).  Using real IPs with a real DNS server should be very similar.
+
-
 
+
-
*For simplicity, this domain only has one server (server.example.fake) and one client (client1.example.fake).
+
-
 
+
-
*This example is running on a NAT'd private network, so I just turned off the firewall on the server!  You probably shouldn't do that!  You'll need to allow traffic on:
+
-
** port 53 (TCP and UDP) for named
+
-
** port 80, 443 (TCP) for httpd (FreeIPA web interface)
+
-
** ports 88 and 464 (TCP and UDP) for Kerberos
+
-
** ports 389, 636 (TCP and UDP) for LDAP
+
-
** ports 123 (UDP) for NTP (network time protocol)
+
-
** port 2049 (TCP and UDP) for NFS
+
-
 
+
-
*All commands are run as root on both the client and server.  Either login as root or prepend "sudo " to each command.
+
-
 
+
-
= Configure DNS realm =
+
-
 
+
-
You might not need to do this.  If you're just setting up a client of FreeIPA, you can skip this section entirely. 
+
-
 
+
-
== Configure existing DNS realm ==
+
-
 
+
-
Make sure the full DNS names and reverse mappings for server(s) and client(s) are in DNS.
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# nslookup server.example.fake
+
-
Server: 192.168.56.20
+
-
Address: 192.168.56.20#53
+
-
 
+
-
Name: server.example.fake
+
-
Address: 192.168.56.20
+
-
 
+
-
[root@client1 ~]# nslookup 192.168.56.20
+
-
Server: 192.168.56.20
+
-
Address: 192.168.56.20#53
+
-
 
+
-
20.56.168.192.in-addr.arpa name = server.example.fake.
+
-
 
+
-
[root@client1 ~]# nslookup client1.example.fake
+
-
Server: 192.168.56.20
+
-
Address: 192.168.56.20#53
+
-
 
+
-
Name: client1.example.fake
+
-
Address: 192.168.56.40
+
-
 
+
-
[root@client1 ~]# nslookup 192.168.56.40
+
-
Server: 192.168.56.20
+
-
Address: 192.168.56.20#53
+
-
 
+
-
40.56.168.192.in-addr.arpa name = client1.example.fake.
+
-
</pre>
+
-
 
+
-
Add the service entries for FreeIPA auto discovery. They are of the form:
+
-
 
+
-
<pre>
+
-
; DNS auto discovery of services
+
-
_ldap._tcp      SRV 10 10 389 server.example.fake.
+
-
_kerberos._udp  SRV 10 10 88 server.example.fake.
+
-
_kerberos._tcp  SRV 10 10 88 server.example.fake.
+
-
</pre>
+
-
 
+
-
== Create a new DNS realm ==
+
-
 
+
-
If you are setting up a new domain, follow these instructions: [[Fake_DNS_Realm|Create a fake DNS realm for testing]].  If you are making a real DNS zone, these instructions should point you in the right direction.
+
-
 
+
-
= Install and configure the FreeIPA server =
+
-
 
+
-
Install and configure the FreeIPA software on the server (server.example.fake).
+
-
 
+
-
== Install the FreeIPA server and admintools package ==
+
-
 
+
-
This step fetches and installs FreeIPA and it's dependencies.  It will install around 100 packages, depending on what you already have installed.
+
-
 
+
-
<pre>
+
-
[root@server ~]# yum install freeipa-server freeipa-admintools
+
-
</pre>
+
-
 
+
-
== Configure FreeIPA server ==
+
-
 
+
-
Run the '''ipa-server-install''' program.  This takes a while.
+
-
 
+
-
All of the default answers should work if DNS hostnames and services are set up correctly and the full domain name is returned by hostname.
+
-
 
+
-
<pre>
+
-
[root@server ~]# ipa-server-install
+
-
 
+
-
The log file for this installation can be found in /var/log/ipaserver-install.log
+
-
==============================================================================
+
-
This program will set up the FreeIPA Server.
+
-
 
+
-
This includes:
+
-
  * Configure the Network Time Daemon (ntpd)
+
-
  * Create and configure an instance of Directory Server
+
-
  * Create and configure a Kerberos Key Distribution Center (KDC)
+
-
  * Configure Apache (httpd)
+
-
 
+
-
To accept the default shown in brackets, press the Enter key.
+
-
 
+
-
Enter the fully qualified domain name of the computer
+
-
on which you're setting up server software. Using the form
+
-
<hostname>.<domainname>
+
-
Example: master.example.com.
+
-
 
+
-
 
+
-
Server host name [server.example.fake]:
+
-
 
+
-
The domain name has been calculated based on the host name.
+
-
 
+
-
Please confirm the domain name [example.fake]:
+
-
 
+
-
The IPA Master Server will be configured with
+
-
Hostname:    server.example.fake
+
-
IP address:  192.168.56.20
+
-
Domain name: example.fake
+
-
 
+
-
The kerberos protocol requires a Realm name to be defined.
+
-
This is typically the domain name converted to uppercase.
+
-
 
+
-
Please provide a realm name [EXAMPLE.FAKE]:
+
-
Certain directory server operations require an administrative user.
+
-
This user is referred to as the Directory Manager and has full access
+
-
to the Directory for system management tasks and will be added to the
+
-
instance of directory server created for IPA.
+
-
The password must be at least 8 characters long.
+
-
 
+
-
Directory Manager password:
+
-
Password (confirm):
+
-
 
+
-
The IPA server requires an administrative user, named 'admin'.
+
-
This user is a regular system account used for IPA server administration.
+
-
 
+
-
IPA admin password:
+
-
Password (confirm):
+
-
 
+
-
 
+
-
The following operations may take some minutes to complete.
+
-
Please wait until the prompt is returned.
+
-
 
+
-
Configuring ntpd
+
-
  [1/4]: stopping ntpd
+
-
  [2/4]: writing configuration
+
-
  [3/4]: configuring ntpd to start on boot
+
-
  [4/4]: starting ntpd
+
-
done configuring ntpd.
+
-
Configuring directory server for the CA: Estimated time 30 seconds
+
-
  [1/3]: creating directory server user
+
-
  [2/3]: creating directory server instance
+
-
  [3/3]: restarting directory server
+
-
done configuring pkids.
+
-
Configuring certificate server: Estimated time 6 minutes
+
-
  [1/17]: creating certificate server user
+
-
  [2/17]: creating pki-ca instance
+
-
  [3/17]: restarting certificate server
+
-
  [4/17]: configuring certificate server instance
+
-
  [5/17]: restarting certificate server
+
-
  [6/17]: creating CA agent PKCS#12 file in /root
+
-
  [7/17]: creating RA agent certificate database
+
-
  [8/17]: importing CA chain to RA certificate database
+
-
  [9/17]: restarting certificate server
+
-
  [10/17]: requesting RA certificate from CA
+
-
  [11/17]: issuing RA agent certificate
+
-
  [12/17]: adding RA agent as a trusted user
+
-
  [13/17]: fixing RA database permissions
+
-
  [14/17]: setting up signing cert profile
+
-
  [15/17]: set up CRL publishing
+
-
  [16/17]: configuring certificate server to start on boot
+
-
  [17/17]: restarting certificate server
+
-
done configuring pki-cad.
+
-
Configuring directory server: Estimated time 1 minute
+
-
  [1/32]: creating directory server user
+
-
  [2/32]: creating directory server instance
+
-
  [3/32]: adding default schema
+
-
  [4/32]: enabling memberof plugin
+
-
  [5/32]: enabling referential integrity plugin
+
-
  [6/32]: enabling winsync plugin
+
-
  [7/32]: configuring replication version plugin
+
-
  [8/32]: enabling IPA enrollment plugin
+
-
  [9/32]: enabling ldapi
+
-
  [10/32]: configuring uniqueness plugin
+
-
  [11/32]: configuring uuid plugin
+
-
  [12/32]: configuring modrdn plugin
+
-
  [13/32]: enabling entryUSN plugin
+
-
  [14/32]: configuring lockout plugin
+
-
  [15/32]: creating indices
+
-
  [16/32]: configuring ssl for ds instance
+
-
  [17/32]: configuring certmap.conf
+
-
  [18/32]: configure autobind for root
+
-
  [19/32]: restarting directory server
+
-
  [20/32]: adding default layout
+
-
  [21/32]: adding delegation layout
+
-
  [22/32]: adding replication acis
+
-
  [23/32]: configuring user private groups
+
-
  [24/32]: configuring netgroups from hostgroups
+
-
  [25/32]: creating default Sudo bind user
+
-
  [26/32]: creating default HBAC rule allow_all
+
-
  [27/32]: initializing group membership
+
-
  [28/32]: adding master entry
+
-
  [29/32]: configuring Posix uid/gid generation
+
-
  [30/32]: enabling compatibility plugin
+
-
  [31/32]: tuning directory server
+
-
  [32/32]: configuring directory to start on boot
+
-
done configuring dirsrv.
+
-
Configuring Kerberos KDC: Estimated time 30 seconds
+
-
  [1/14]: setting KDC account password
+
-
  [2/14]: adding sasl mappings to the directory
+
-
  [3/14]: adding kerberos entries to the DS
+
-
  [4/14]: adding default ACIs
+
-
  [5/14]: configuring KDC
+
-
  [6/14]: adding default keytypes
+
-
  [7/14]: adding default password policy
+
-
  [8/14]: creating a keytab for the directory
+
-
  [9/14]: creating a keytab for the machine
+
-
  [10/14]: exporting the kadmin keytab
+
-
  [11/14]: adding the password extension to the directory
+
-
  [12/14]: adding the kerberos master key to the directory
+
-
  [13/14]: starting the KDC
+
-
  [14/14]: configuring KDC to start on boot
+
-
done configuring krb5kdc.
+
-
Configuring ipa_kpasswd
+
-
  [1/2]: starting ipa_kpasswd
+
-
  [2/2]: configuring ipa_kpasswd to start on boot
+
-
done configuring ipa_kpasswd.
+
-
Configuring the web interface: Estimated time 1 minute
+
-
  [1/12]: disabling mod_ssl in httpd
+
-
  [2/12]: setting mod_nss port to 443
+
-
  [3/12]: setting mod_nss password file
+
-
  [4/12]: adding URL rewriting rules
+
-
  [5/12]: configuring httpd
+
-
  [6/12]: setting up ssl
+
-
  [7/12]: setting up browser autoconfig
+
-
  [8/12]: publish CA cert
+
-
  [9/12]: creating a keytab for httpd
+
-
  [10/12]: configuring SELinux for httpd
+
-
  [11/12]: restarting httpd
+
-
  [12/12]: configuring httpd to start on boot
+
-
done configuring httpd.
+
-
Setting the certificate subject base
+
-
restarting certificate server
+
-
Applying LDAP updates
+
-
Restarting the directory server
+
-
Restarting the KDC
+
-
Restarting the web server
+
-
Sample zone file for bind has been created in /tmp/sample.zone.I_fDwT.db
+
-
==============================================================================
+
-
Setup complete
+
-
 
+
-
Next steps:
+
-
1. You must make sure these network ports are open:
+
-
TCP Ports:
+
-
  * 80, 443: HTTP/HTTPS
+
-
  * 389, 636: LDAP/LDAPS
+
-
  * 88, 464: kerberos
+
-
UDP Ports:
+
-
  * 88, 464: kerberos
+
-
  * 123: ntp
+
-
 
+
-
2. You can now obtain a kerberos ticket using the command: 'kinit admin'
+
-
  This ticket will allow you to use the IPA tools (e.g., ipa user-add)
+
-
  and the web user interface.
+
-
 
+
-
Be sure to back up the CA certificate stored in /root/cacert.p12
+
-
This file is required to create replicas. The password for this
+
-
file is the Directory Manager password
+
-
</pre>
+
-
 
+
-
= Install and configure FreeIPA client(s) =
+
-
 
+
-
Install the '''freeipa-client''' package on each client of the FreeIPA domain.
+
-
 
+
-
== Install the FreeIPA client package ==
+
-
 
+
-
Fetch and install the FreeIPA client.
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# yum install freeipa-client
+
-
...
+
-
</pre>
+
-
 
+
-
== Configure the FreeIPA client package (OOPS!) ==
+
-
 
+
-
Again, if DNS is setup correctly and '''hostname''' returns the full DNS name, the default answers should work.
+
-
 
+
-
You want to use "admin" (the administrator user you created when configuring the FreeIPA server) as the enrollment principal.
+
-
 
+
-
Oh no! Currently, Fedora 15 gives me this problem:
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# ipa-client-install
+
-
Discovery was successful!
+
-
Hostname: client1.example.fake
+
-
Realm: EXAMPLE.FAKE
+
-
DNS Domain: example.fake
+
-
IPA Server: server.example.fake
+
-
BaseDN: dc=example,dc=fake
+
-
 
+
-
 
+
-
Continue to configure the system with these values? [no]: yes
+
-
Enrollment principal: admin
+
-
Password for admin@EXAMPLE.FAKE:
+
-
 
+
-
Joining realm failed because of failing XML-RPC request.
+
-
  This error may be caused by incompatible server/client major versions.
+
-
</pre>
+
-
 
+
-
This problem is easily worked around, but you may not need to - I'm sure this will be fixed soon.
+
-
 
+
-
== Configure the FreeIPA client package (The Workaround) ==
+
-
 
+
-
The problem and workaround are described here: https://www.redhat.com/archives/freeipa-users/2011-July/msg00029.html
+
-
 
+
-
=== Get credentials and add the host to FreeIPA ===
+
-
 
+
-
Both of these commands should be run on the '''*server*'''.
+
-
 
+
-
First, get admin credentials.  If you are configuring multiple clients, this only needs to be run the first time.
+
-
 
+
-
<pre>
+
-
[root@server ~]# kinit admin
+
-
Password for admin@EXAMPLE.FAKE:
+
-
</pre>
+
-
 
+
-
Now that you have credentials, you can add the client to FreeIPA.
+
-
 
+
-
<pre>
+
-
[root@server ~]# ipa host-add client1.example.fake
+
-
---------------------------------
+
-
Added host "client1.example.fake"
+
-
---------------------------------
+
-
  Host name: client1.example.fake
+
-
  Principal name: host/client1.example.fake@EXAMPLE.FAKE
+
-
  Managed by: client1.example.fake
+
-
</pre>
+
-
 
+
-
=== (Force) Configure FreeIPA client ===
+
-
 
+
-
Back on the client now.  Run ipa-client-install again, but this time use the ''--force'' flag:
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# ipa-client-install --force
+
-
Discovery was successful!
+
-
Hostname: client1.example.fake
+
-
Realm: EXAMPLE.FAKE
+
-
DNS Domain: example.fake
+
-
IPA Server: server.example.fake
+
-
BaseDN: dc=example,dc=fake
+
-
 
+
-
 
+
-
Continue to configure the system with these values? [no]: yes
+
-
Enrollment principal: admin
+
-
Password for admin@EXAMPLE.FAKE:
+
-
 
+
-
Joining realm failed because of failing XML-RPC request.
+
-
  This error may be caused by incompatible server/client major versions.
+
-
  Use ipa-getkeytab to obtain a host principal for this server.
+
-
Created /etc/ipa/default.conf
+
-
Configured /etc/sssd/sssd.conf
+
-
Configured /etc/krb5.conf for IPA realm EXAMPLE.FAKE
+
-
Failed to configure automatic startup of the NSCD daemon
+
-
SSSD enabled
+
-
nss_ldap is not able to use DNS discovery!
+
-
Changing configuration to use hardcoded server name: server.example.fake
+
-
Kerberos 5 enabled
+
-
NTP enabled
+
-
Client configuration complete.
+
-
</pre>
+
-
 
+
-
=== Manually fetch the keytab entry for the client ===
+
-
+
-
The last step of the workaround is to fetch the client's own keytab entry that '''ipa-client-install''' wasn't able to get.
+
-
 
+
-
To do this, you'll need to authenticate as admin again, but this time on the client:
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# kinit admin
+
-
Password for admin@EXAMPLE.FAKE:
+
-
</pre>
+
-
 
+
-
Now run '''ipa-getkeytab''' on the client for the host keytab entries:
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# ipa-getkeytab -s server.example.fake -p host/client1.example.fake -k /etc/krb5.keytab
+
-
Keytab successfully retrieved and stored in: /etc/krb5.keytab
+
-
</pre>
+
-
 
+
-
Now, FreeIPA should be setup on the client.
+
-
 
+
-
= Add FreeIPA NFS service for each host =
+
-
 
+
-
The next step is to setup kerberos principals for the NFS service on each host.
+
-
 
+
-
== Add FreeIPA NFS service for server ==
+
-
 
+
-
<pre>
+
-
[root@server ~]# ipa service-add nfs/server.example.fake
+
-
----------------------------------------------------
+
-
Added service "nfs/server.example.fake@EXAMPLE.FAKE"
+
-
----------------------------------------------------
+
-
  Principal: nfs/server.example.fake@EXAMPLE.FAKE
+
-
  Managed by: server.example.fake
+
-
</pre>
+
-
 
+
-
== Add FreeIPA NFS service for client(s) ==
+
-
 
+
-
<pre>
+
-
[root@server ~]# ipa service-add nfs/client1.example.fake
+
-
-----------------------------------------------------
+
-
Added service "nfs/client1.example.fake@EXAMPLE.FAKE"
+
-
-----------------------------------------------------
+
-
  Principal: nfs/client1.example.fake@EXAMPLE.FAKE
+
-
  Managed by: client1.example.fake
+
-
</pre>
+
-
 
+
-
== Import FreeIPA NFS service tickets on the server ==
+
-
 
+
-
Again, we have to fetch a keytab entry.  This time, it's for the nfs service of the local host.
+
-
 
+
-
According to [http://docs.redhat.com/docs/en-US/Red_Hat_Enterprise_Linux/6/html/Enterprise_Identity_Management_Guide/sect-Enterprise_Identity_Management_Guide-Configuring_Service_Principals-Configuring_an_NFS_Service_Principal_on_the_IPA_Server.html this], we need to specify the enc type "des-cbc-crc".
+
-
 
+
-
<pre>
+
-
[root@server ~]# ipa-getkeytab -s server.example.fake -e des-cbc-crc -p nfs/server.example.fake -k /etc/krb5.keytab
+
-
Keytab successfully retrieved and stored in: /etc/krb5.keytab
+
-
</pre>
+
-
 
+
-
You can check to see what's in the keytab like this:
+
-
 
+
-
<pre>
+
-
[root@server ~]# klist -ke /etc/krb5.keytab
+
-
Keytab name: WRFILE:/etc/krb5.keytab
+
-
KVNO Principal
+
-
---- --------------------------------------------------------------------------
+
-
  6 nfs/server.example.fake@EXAMPLE.FAKE (des-cbc-crc)
+
-
  4 host/server.example.fake@EXAMPLE.FAKE (aes256-cts-hmac-sha1-96)
+
-
  4 host/server.example.fake@EXAMPLE.FAKE (aes128-cts-hmac-sha1-96)
+
-
  4 host/server.example.fake@EXAMPLE.FAKE (des3-cbc-sha1)
+
-
  4 host/server.example.fake@EXAMPLE.FAKE (arcfour-hmac)
+
-
  4 host/server.example.fake@EXAMPLE.FAKE (des-cbc-crc)
+
-
</pre>
+
-
 
+
-
== Import FreeIPA NFS service tickets on the client(s) ==
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# ipa-getkeytab -s server.example.fake -e des-cbc-crc -p nfs/client1.example.fake -k /etc/krb5.keytab
+
-
Keytab successfully retrieved and stored in: /etc/krb5.keytab
+
-
</pre>
+
-
 
+
-
And here's what /etc/krb5.kettab has in it:
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# klist -ke /etc/krb5.keytab
+
-
Keytab name: WRFILE:/etc/krb5.keytab
+
-
KVNO Principal
+
-
---- --------------------------------------------------------------------------
+
-
  6 nfs/client1.example.fake@EXAMPLE.FAKE (des-cbc-crc)
+
-
  3 host/client1.example.fake@EXAMPLE.FAKE (aes256-cts-hmac-sha1-96)
+
-
  3 host/client1.example.fake@EXAMPLE.FAKE (aes128-cts-hmac-sha1-96)
+
-
  3 host/client1.example.fake@EXAMPLE.FAKE (des3-cbc-sha1)
+
-
  3 host/client1.example.fake@EXAMPLE.FAKE (arcfour-hmac)
+
-
  3 host/client1.example.fake@EXAMPLE.FAKE (des-cbc-crc)
+
-
</pre>
+
-
 
+
-
= Turn on "Secure NFS" on both client(s) and server =
+
-
 
+
-
This turns on NFS secure mounts and enables rpc.gssd and rpc.svcgssd.
+
-
 
+
-
Edit these lines in file "/etc/sysconfig/nfs":
+
-
 
+
-
<pre>
+
-
# Set to turn on Secure NFS mounts.
+
-
SECURE_NFS="yes"
+
-
# Optional arguments passed to rpc.gssd. See rpc.gssd(8)
+
-
RPCGSSDARGS="-vvv"
+
-
# Optional arguments passed to rpc.svcgssd. See rpc.svcgssd(8)
+
-
RPCSVCGSSDARGS="-vvv"
+
-
</pre>
+
-
 
+
-
The -vvv flags are for better debugging output in file "/var/log/messages".
+
-
 
+
-
To pick up the changes, you must restart nfs services:
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# service nfs restart
+
-
Restarting nfs (via systemctl):                            [  OK  ]
+
-
[root@client1 ~]# service rpcgssd restart
+
-
Restarting rpcgssd (via systemctl):                        [  OK  ]
+
-
[root@client1 ~]# service rpcsvcgssd restart
+
-
Restarting rpcsvcgssd (via systemctl):                    [  OK  ]
+
-
</pre>
+
-
 
+
-
This must be run on both clients and servers.
+
-
 
+
-
= Hosts' full DNS name in /etc/hosts =
+
-
 
+
-
NFS util program 'rpc.gssd' (XXX ???) requires that the full dns name of the host be in /etc/hosts.  The full DNS name must be the only entry on that line.
+
-
 
+
-
On the server:
+
-
 
+
-
<pre>
+
-
[root@server ~]# cat /etc/hosts
+
-
127.0.0.1  localhost localhost.localdomain localhost4 localhost4.localdomain4
+
-
::1        localhost localhost.localdomain localhost6 localhost6.localdomain6
+
-
 
+
-
192.168.56.20 server.example.fake
+
-
</pre>
+
-
 
+
-
This must be done on the client(s) as well:
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# cat /etc/hosts
+
-
127.0.0.1  localhost localhost.localdomain localhost4 localhost4.localdomain4
+
-
::1        localhost localhost.localdomain localhost6 localhost6.localdomain6
+
-
 
+
-
192.168.56.40 client1.example.fake
+
-
</pre>
+
-
 
+
-
= Set up /etc/exports on the server =
+
-
 
+
-
Edit file "/etc/exports".  This makes one krb5 mountpoint of /export to be mounted as "/" (thats the fsid=0 part):
+
-
 
+
-
<pre>
+
-
/export gss/krb5(rw,fsid=0,no_subtree_check,no_root_squash)
+
-
</pre>
+
-
 
+
-
Now exportfs should show the mount:
+
-
 
+
-
<pre>
+
-
[root@server ~]# exportfs -av
+
-
exportfs: scandir /etc/exports.d: No such file or directory
+
-
 
+
-
exporting gss/krb5:/export
+
-
</pre>
+
-
 
+
-
Restart nfs:
+
-
 
+
-
<pre>
+
-
[root@server ~]# service nfs restart
+
-
Restarting nfs (via systemctl):                            [  OK  ]
+
-
</pre>
+
-
 
+
-
= Allow Kerberos to use "weak crypto" =
+
-
 
+
-
To use the des key kerberos must be told to allow "weak" crypto.  Newer kernels and nfsutils allow the use of AES, etc.
+
-
 
+
-
Edit file '/etc/krb5.conf':
+
-
 
+
-
In section "libdefaults", add the line:
+
-
 
+
-
<pre>
+
-
allow_weak_crypto = true
+
-
</pre>
+
-
 
+
-
The "libdefaults" section should look something like this:
+
-
 
+
-
<pre>
+
-
[libdefaults]
+
-
  default_realm = EXAMPLE.FAKE
+
-
  dns_lookup_realm = false
+
-
  dns_lookup_kdc = false
+
-
  rdns = false
+
-
  ticket_lifetime = 24h
+
-
  forwardable = yes
+
-
  allow_weak_crypto = true
+
-
</pre>
+
-
 
+
-
= Mount the filesystem =
+
-
 
+
-
The moment of truth!  If you run in to problems, see [[ProblemsMounting|Problems Mounting]].
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# mount -v -t nfs4 -o sec=krb5 server.example.fake:/ /mnt
+
-
mount.nfs4: timeout set for Tue Jul 19 22:36:46 2011
+
-
mount.nfs4: trying text-based options 'sec=krb5,addr=192.168.56.20,clientaddr=192.168.56.40'
+
-
server.example.fake:/ on /mnt type nfs4 (rw,sec=krb5)
+
-
</pre>
+
-
 
+
-
Now test it:
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# echo "test" > /mnt/example.com
+
-
[root@client1 ~]# cat /mnt/example.com
+
-
test
+
-
</pre>
+
-
 
+
-
= Test the NFS mount as another user =
+
-
 
+
-
This section just covers testing the NFS mount with other users.
+
-
 
+
-
== Add another user ==
+
-
 
+
-
First, we need to add another user to FreeIPA.
+
-
 
+
-
This must be run with credentials. On the '''server''', run:
+
-
 
+
-
<pre>
+
-
[root@server ~]# ipa user-add someguy
+
-
First name: guy
+
-
Last name: someone
+
-
--------------------
+
-
Added user "someguy"
+
-
--------------------
+
-
  User login: someguy
+
-
  First name: guy
+
-
  Last name: someone
+
-
  Full name: guy someone
+
-
  Display name: guy someone
+
-
  Initials: gs
+
-
  Home directory: /home/someguy
+
-
  GECOS field: guy someone
+
-
  Login shell: /bin/sh
+
-
  Kerberos principal: someguy@EXAMPLE.FAKE
+
-
  UID: 25400004
+
-
</pre>
+
-
 
+
-
Now set a temporary password for the user.  The first time the user logs in, they must change it to something new.
+
-
 
+
-
<pre>
+
-
[root@server ~]# ipa passwd someguy
+
-
Password:
+
-
Enter Password again to verify:
+
-
-------------------------------------------
+
-
Changed password for "someguy@EXAMPLE.FAKE"
+
-
-------------------------------------------
+
-
</pre>
+
-
 
+
-
== Test NFS ==
+
-
 
+
-
Now there is a new user on the client(s)!
+
-
 
+
-
<pre>
+
-
[root@client1 ~]# su someguy
+
-
sh-4.2$ id
+
-
uid=25400004(someguy) gid=25400004(someguy) groups=25400004(someguy),25400001(ipausers) context=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023
+
-
</pre>
+
-
 
+
-
Authenticate as the user:
+
-
 
+
-
<pre>
+
-
sh-4.2$ kinit
+
-
Password for someguy@EXAMPLE.FAKE:
+
-
Password expired.  You must change it now.
+
-
Enter new password:
+
-
Enter it again:
+
-
</pre>
+
-
 
+
-
Now test NFS:
+
-
 
+
-
<pre>
+
-
sh-4.2$ echo bar > /mnt/foo
+
-
sh-4.2$ cat /mnt/foo
+
-
bar
+
-
sh-4.2$ ls -l /mnt
+
-
total 12
+
-
-rw-r--r--. 1 nobody  nobody  4 Jul 19 17:22 bar
+
-
-rw-r--r--. 1 nobody  nobody  5 Jul 19 22:35 example.com
+
-
-rw-r--r--. 1 someguy someguy 4 Jul 19 22:44 foo
+
-
</pre>
+

Latest revision as of 02:48, 1 March 2012

This has been moved to NFS and FreeIPA.

Retrieved from "http://linux-nfs.org/wiki/index.php/FreeIPA_and_NFSv4"
Personal tools